1. Application status of internal powder feeding plasma spray gun
1. Application status of internal powder feeding plasma spray gun
1.内部送粉等离子喷枪的应用现状
1, the application status of incoming powder plasma spray gun
1，来料粉末等离子喷枪的应用状况
无法加载全部结果
重试
正在重试…
正在重试…
无法加载全部结果
重试
正在重试…
正在重试…
Typical internal powder-feeding plasma spray guns include Axial III developed by Northwest Mettch in Canada and SG100 developed by Praxair TAFA. Their structure, characteristics and applications are as follows.
Typical internal powder-feeding plasma spray guns include Axial III developed by Northwest Mettch in Canada and SG100 developed by Praxair TAFA. Their structure, characteristics and applications are as follows.
典型的内部送粉等离子喷枪包括加拿大西北梅特奇（Northwest Mettch）开发的Axial III和普莱克斯（Praxair）TAFA开发的SG100。它们的结构，特征和应用如下。
A typical plasma gun with a powder feed within Axial III Canadian NorthwestMettch developed, Praxair TAFA developed SG100, their structure, characteristics and application as described below.
开发了加拿大Axial III加拿大西北梅特克公司内部带有粉末进料的典型等离子枪，普莱克斯TAFA开发了SG100，其结构，特性和应用如下所述。
无法加载全部结果
重试
正在重试…
正在重试…
无法加载全部结果
重试
正在重试…
正在重试…
1.1, Axial III plasma spray gun
1.1, Axial III plasma spray gun
...
1.1, Axial III plasma torch
...
无法加载全部结果
重试
正在重试…
正在重试…
无法加载全部结果
重试
正在重试…
正在重试…
Axial III is a plasma spray gun developed by Mettch. It uses a three-cathode and three-anode design to achieve axial powder feeding, as shown in Figure 5.
Axial III is a plasma spray gun developed by Mettch. It uses a three-cathode and three-anode design to achieve axial powder feeding, as shown in Figure 5.
Axial III是Mettch开发的等离子喷枪。它采用三阴极和三阳极设计来实现轴向粉末进给，如图5所示。
Axial III is Mettch developed a plasma spray gun, which uses three cathodes, three anode design, in order to effect axial powder feeding, as shown in FIG.
Axial III是Mettch开发的等离子喷枪，它采用三个阴极，三个阳极设计，以实现轴向粉末进给，如图2所示。
无法加载全部结果
重试
正在重试…
正在重试…
无法加载全部结果
重试
正在重试…
正在重试…
Table 2 Physical parameters of WC-10Co-4Cr spray powder
Table 3 Spraying process parameters
Table 3 Spraying process parameters
表3喷涂工艺参数
Table 3 Spraying Parameters
表3喷涂参数
无法加载全部结果
重试
正在重试…
正在重试…
无法加载全部结果
重试
正在重试…
正在重试…
2. Experimental results and discussion
2. Experimental results and discussion
2.实验结果与讨论
无法加载全部结果
重试
正在重试…
正在重试…
无法加载全部结果
重试
正在重试…
正在重试…
2.1. Coating bonding strength
2.1. Coating bonding strength
2.1。涂层粘结强度
2.1, the coating binding strength
2.1，涂层的结合强度
无法加载全部结果
重试
正在重试…
正在重试…
无法加载全部结果
重试
正在重试…
正在重试…
This paper uses WDW100A microcomputer-controlled electronic universal testing machine to test the bonding strength of the coating. The testing standard is implemented in accordance with the national standard GB8642-2002.
This paper uses WDW100A microcomputer-controlled electronic universal testing machine to test the bonding strength of the coating. The testing standard is implemented in accordance with the national standard GB8642-2002.
本文使用WDW100A微机控制的电子万能试验机来测试涂层的粘结强度。测试标准按照国家标准GB8642-2002执行。
In this thesis WDW100A computer-controlled electronic universal testing machine, the binding strength of the coating test, testing standards by GB GB8642-2002 performed.
本文采用WDW100A计算机控制的电子万能试验机，对涂层的结合强度进行试验，试验标准按GB GB8642-2002执行。
无法加载全部结果
重试
正在重试…
正在重试…
Experimental conditions: WDW100A microcomputer-controlled electronic universal testing machine, glue: E7 glue, displacement speed: 1.0mm/min, room temperature: 20°C.
Experimental conditions: WDW100A microcomputer-controlled electronic universal testing machine, glue: E7 glue, displacement speed: 1.0mm/min, room temperature: 20°C.
实验条件：WDW100A微机控制电子万能试验机，胶水：E7胶，位移速度：1.0mm / min，室温：20℃。
Experimental conditions: WDW100A computer-controlled electronic universal testing machine, viscose: E7 gum, displacement speed: 1.0mm / min, temperature: 20 ℃.
实验条件：WDW100A计算机控制的电子万能试验机，粘胶：E7胶，位移速度：1.0mm / min，温度：20℃。
无法加载全部结果
重试
正在重试…
正在重试…
The test results are shown in Table 4.
The test results are shown in Table 4.
测试结果列于表4。
无法加载全部结果
重试
正在重试…
正在重试…
无法加载全部结果
重试
正在重试…
正在重试…
Table 4 Bond strength test table
Hot information
Copyright © 2016-2018 Chengdu WOCO Carbide Industry Co., Ltd. All Rights Reserved.
